Brunton Camping Equipment MM08 User Manual

time  
The time function works as a normal clock.  
Press ADJUST to display date  
setting the time  
Press and hold ADJUST for 2 seconds. The Hour digit will start flashing  
Turn the measuring wheel to increase / decrease the value (clockwise to increase or counter- clockwise  
to decrease).  
Press ADJUST to confirm and switch to minute setting.  
Turn the measuring wheel to set minutes.  
M A P M E A S U R E R  
Product overview  
1. LCD  
Press ADJUST to confirm and switch to seconds setting.  
Turn the measuring wheel to reset seconds to zero.  
Press the ADJUST key to confirm  
2. Measuring wheel  
3. Measure button  
4. LCD backlight button  
5. ADJUST button  
6. MODE button  
Continue the setting of 12/24 hour, Month, Date and Year  
setting the alarm  
7. Battery compartment  
8. Attachment clip  
9. Reference arrow  
Press MODE repeatedly until “ALARM” is displayed.  
Press and hold ADJUST for 2 seconds to set the alarm. The Hour digit will start flashing.  
Turn the measuring wheel to increase / decrease the value (clockwise to increase or counter clockwise  
to decrease).  
Press ADJUST to confirm and switch to minute setting.  
Turn the measuring wheel to set minutes.  
The MM-08 Map Measurer is the designed for use with virtually any map. It will measure travel distance  
in miles, km and nautical miles, calculate estimated travel time and has a countdown timer that shows  
remaining time to your destination. To get the most out of your purchase, be sure to carefully read this  
manual and keep it on hand for later reference.  
Press the ADJUST to confirm  
An alarm icon will indicate the alarm is activated.  
Press ADJUST in alarm mode to turn ON/OFF the alarm.  
An LCD sticker is placed on the LCD glass of this unit when purchased. Please make sure to remove the  
sticker before use.  
Battery installation  
Unscrew the clip from the body with a screwdriver.  
Open the battery compartment cover by using a coin (turn counter clockwise).  
Place the new battery, CR2032, into the battery compartment with the positive (+) side facing up.  
With the O-ring in the correct position, close the battery compartments cover (turn clockwise).  
using the MaP Measurer  
The MODE button will take you through the following sequence:  
Time > Alarm > Distance > Time to go > Scale > Speed >  
To set up to use follow the following steps:  
care and Maintenance  
Never attempt to disassemble or service your unit.  
setting the Map scale  
Protect the electronic module from extreme heat, shocks and long time exposure to direct sunlight.  
Unit can be wiped clean with a lightly moistened cloth and mild soap.  
Do not expose the unit to strong chemicals such as gasoline, clean solvents, acetone, alcohol, insect  
repellents, as they may damage the unit’s seal, case and finish.  
Store the unit in a dry place when you are not using it.  
It is important to set the correct map scale before measuring distance on the map.  
Press MODE repeatedly until “SCALE” is displayed.  
Press and hold ADJUST for 2 seconds. The display will show 1: 50000 (1:50 000 is the default scale).  
The first zero will start flashing.  
Turn the measuring wheel to increase / decrease the value (clockwise to increase or counter clockwise  
to decrease).  
Press ADJUST to confirm and switch to next digit.  
Adjust digit by digit the same way  
Avoid allowing the unit to come into direct contact with hair gels, perfumes, sun screen, and other toilet-  
ries, which can cause deterioration of the plastic parts.  
Whenever the unit comes into contact with these or other toiletries, wipe it off immediately with a dry, soft  
cloth.  
Exit setting by pressing and holding ADJUST for 2 seconds.  
warranty  
setting your average speed  
Brunton warrants this product to be free of defects in materials and workmanship for a period of two  
years. This warranty extends to the original purchaser from the date of purchase. This warranty is void  
and a charge for repair will be made if the Map Measurer has been damaged by negligence, accident or  
mishandling, or has not been operated in accordance with standard operating procedures, or if the Map  
Measurer was altered or repaired by anyone other than a Brunton repair facility. This warranty gives you  
specific legal rights, and you also have rights, which vary from state to state. No other warranty, expressed  
or implied, applies to the Brunton product, nor is any person or company authorized to assume any other  
warranty for Brunton. Brunton does not assume any responsibility for any consequential damages oc-  
casioned by this product.  
By setting the average speed, the time to go function will calculate the estimated travel time for the  
distance measured – a useful function when planning your daytrip  
Press MODE repeatedly until “SPEED” is displayed.  
Press ADJUST repeatedly to set speed unit (km/h, mph, knots)  
Press and hold ADJUST for 2 seconds. The display will show 005.0 km/h (5.0 km/h, 3.1 mph or 2.7  
knots is the default speed, depending on the selected unit). The first zero will start flashing.  
Turn the measuring wheel to increase / decrease the value (clockwise to increase or counter clockwise  
to decrease).  
Press ADJUST to confirm and switch to next digit.  
Should the product prove defective, contact Brunton, and you will be provided with a Return Authorization  
Number (RA#). Send a copy of your proof of purchase, the RA#, a short description of the problem and  
the product to Brunton at the following address. Brunton suggests insuring the product in case of damage  
or loss in shipment.  
Adjust digit by digit the same way or exit setting by pressing and holding  
Exit setting by pressing and holding ADJUST for 2 seconds.  
Measuring distance on a map  
Press MODE repeatedly until “DISTANCE” is displayed.  
Brunton  
2255 Brunton Court  
Warranty Repair (307) 857-4700  
Press ADJUST repeatedly to set the desired measuring unit (km, mile, nautical mile). This can be done  
anytime during measuring.  
Riverton, WY 82501  
Press MEASURE to activate the measuring function. The “DIST” icon will start flashing.  
Place the measuring wheel at the desired location on the map and start  
measuring by rolling the measuring wheel along the desired route. When  
starting and ending the measurement, make sure the Reference arrow  
points at the start and stop of the route.  
To get the best accuracy; drag the map measurer in a slow and steady pace  
(not faster than 5 cm/sec, 2 inch/sec), hold the map measurer as a pen and  
use the palm of your hand as a support to the surface.  
Please return within 30 days of purchase  
It doesn’t matter in which direction the distance is measured. By changing  
direction you can deduct distance. This is useful if you need to correct the  
measured route – simply roll back along the incorrect part of the route and  
continue measuring.  
Name: ________________________________________________________________________________  
Address: ______________________________________________________________________________  
City: _______________________ State: __________________ Zip Code :__________________________  
Phone : _____________________________________ Email: ____________________________________  
Date Purchased: ________________________________________________________________________  
Press MEASURE again to deactivate the measuring function. This will lock  
the value and prevent it from being accidentally adjusted.  
Press MEASURE again to resume the measurement.  
Reset measurement by pressing and holding ADJUST for 2 seconds.  
NOTE: To reach any other mode, the Map measuring function needs to be deactivated.  
Would you like to receive a Brunton catalog? ( )Yes ( )No  
Please let us know where you purchased your MM08?  
tiMe-to-go  
Once you got the distance measured, the time to go function will show you the required travel time to  
destination at your stored speed  
Store Name: ___________________________________________________________________________  
City: _______________________ State: ____________ Zip Code: ________________________________  
( ) Online site _________________ ( ) Catalog ________________________________________________  
( ) Gift ( ) Brunton ( ) Other ________________________________________________________________  
Press MODE repeatedly until “TIME – TO - GO” is displayed.  
The calculated time required (based on the set speed) will be displayed.  
Press ADJUST to start the timer and start travel towards your destination.  
Press ADJUST to pause the timer and press ADJUST again to resume.  
Reset the count down timer to initial time by pressing and holding ADJUST for 2 seconds.  
Delete time by pressing and holding ADJUST for 2 more seconds. NOTE: This will also delete the  
measured distance!  
Do you own another Brunton product?  
( ) Yes. Product: ____________________________ ( ) No  
 

Belkin Headphones 7 22868 56053 2 User Manual
Black Box Headphones Mobile Headset User Manual
Black Decker Power Supply 90521888 User Manual
Blanco Indoor Furnishings 514 475 User Manual
Bosch Appliances Range HDS252U User Manual
Canon Camcorder 150U User Manual
Canon Camera Flash 577 G User Manual
Canon Camera Lens KJ17EX77B User Manual
Casio Computer Monitor 700AR1A User Manual
Casio Electronic Keyboard CTK 750 User Manual